I have actually a brand-new range through a NEMA 14-50P plug. I discover my 240V receptacle is for a dryer, v the peak blade a 90° one. So I require to change the receptacle out. However, ns think my selection needs 50 Amps, and the 240V circuit breakers are ganged 30 amp. The reason I think this is the cord top top the selection is rated for 50 amps. The installed circuit breakers are kind QP. Space these all plug in circuit breakers?. Is it adequate to just upgrade the currently circuit breakers with 50 amp QP circuit breakers. Is the all i would should do readjust out the circuit breakers, and change the receptacle? perform I require to change the circuit breakers or would the 30 Amp breakers suffice?


*

*

To increase the amp rating of her circuit breaker, you almost certainly need to boost the gauge of every the wiring on the circuit. Circuit breakers space there to defend the wiring because that overloading, overheating, melt the insulation, and eventually starting a fire.

You are watching: How to change a 30 amp breaker to a 50 amp breaker

Typically, you have actually the following wire gauges (this may vary with long circuits and also your neighborhood codes):

15 amps: 14 gauge20 amps: 12 gauge30 amps: 10 gauge55 amps: 8 gauge75 amps: 6 gauge

So going indigenous 30 amps come 55 amps requires you to rewire the circuit from 10 gauge to 8 gauge wiring.

For her oven, examine the specs ~ above the oven itself. It may simply have actually a plug that"s designed because that multiple ovens and also will work-related on a 30 amp circuit.


*

Before you carry out anything else, look in ~ the appliance"s rating plate. That is probably located somewhere within the door or probably on the back.

*

While this one is for an electric clothes dryer, every appliance ratings plates have actually the exact same information. You have the right to see it plainly indicates the amperes required, in this situation 24. So a 30 amp circuit would be fine. If her rating plate indicates less than 25 amps, every is most likely well. Otherwise, a heavier than typical circuit is required.

Begin by transforming off the circuit breaker, open up up the circuit breaker box and the receptacle box and look in ~ the appliance circuit"s wires. If not ancient (1960s or later), the cable gauge is published on castle somewhere. If you can"t find any type of printing, look in ~ the bare wire itself (use a driver to ease the retaining screw and slide the wire the end from the connector) and compare the to well-known wire gauges—another wire in the circuit breaker box, a gauging device, or wire samples native an electric supply store. If the panel and also receptacle ends execute not exactly complement in cable quality, color, number, and also gauge, disregard the remainder of what ns say and call a handyman or electrician (it suggests you have actually the not correct wire, or there is a junction somewhere).

The breaker for the circuit can not exceed the cable rating. The is, a 50 amp breaker cannot be supplied on a cable rated because that 30 amperes: doing so would allow the wire to overheat bring about a home fire.
BMitch"s table of worths is only for copper wiring for lengths as much as 80–100 feet (25–30 m). Smaller sized capacities use to aluminum wire and also for much longer wire runs. It would certainly be unusual to discover a smaller installed breaker 보다 the wire can handle, however it is acceptable. (I have actually done this in special situations in my residence to defend the an equipment as well together the home wiring as soon as I knew a lot around the details appliance installed—such together an electric vehicle.)

U.S. Range circuits room most generally intended for a 40 amp appliance (240 volts time 40 amps is 9,600 watts—with a 20% derating for continuous use, that way the most the circuit have the right to use is 7,680 watts). Many run the the mill electric range/ovens are rated at 4,000 watts.

See more: Solved: 12 Is 40 Percent Of What Number Is 12? Answer: 30

The form of cord ("pigtail") ~ above the appliance is no necessarily indicative the its rating. A 50 amp pigtail and also outlet is fine because that a 30 amp circuit and appliance, though maybe confusing. An extra hefty component walk not increase the circuit capacity—that is established by the weakest link. If someone mounted a 50 amp pigtail and also outlet, however the appliance only needs 30 amps and also the wire is 10 gauge, there is nothing to do—it is fine together is.

However, if the appliance needs more than the wires" rating, there space several means to proceed:

Replace the housewire with suitably heavier gauge wire. This is the many disruptive if sheetrock needs to be torn out. Or maybe the wiring is already exposed or in conduit? That would be lot easier.Reconfigure the appliance to use much less power. In a dryer, there are numerous heating elements, say three 2 kW elements. Disconnecting one would certainly limit power usage to 4 kW (= 4,000 watts) to add the power necessary for the motor (usually 250–400 watts). Because that ranges, disconnecting few of the burners would decrease the maximum feasible use.Replace the appliance v a much less demanding one. (Maybe the is time because that a gas appliance instead?)