In mine rebuilding task I have actually counted 18 outlets and lights on one bedroom circuit that travels through 3 rooms. Is that ok?




You are watching: How many outlets on a 15 amp circuit breaker

Also, examine your breaker. You deserve to have as many outlets ~ above a solitary circuit as you like*, yet you need to be careful since you have the right to only traction so much existing from the circuit in ~ a time. because that example, don"t suppose to run an electric chainsaw and a vacuum at the exact same time turn off a single 15A circuit. If you have actually a 15A breaker attached which is likely the case, I would recommend not running any major appliances (Such together a Microwave or window AC unit) turn off of it, because that will take up most of your juice, and also one too numerous lamps in the other 17 outlets could trip her breaker. If you must run a heavy appliance, just wire in an additional circuit, and don"t drill a hole through the wires close to the breaker crate (Voice that experience).

*Some locations such as Belgium border you to 8 outlets on a circuit, or you violate wiring code.

improve this prize
edited Dec 12 "18 in ~ 22:50

21633 silver badges1212 bronze title
answered Nov 17 "14 in ~ 11:19

1,31077 silver badges1717 bronze badges
add a comment |
Depends where you are and also for what worth of yes sir you space looking. So lengthy as the breaker is 15 amps it have to be "safe."
Ratchet Freak mentions a details numerical limitation in Belgium. Other human being have stated some assessors in the US having actually an expectation of "around 7" yet I don"t think code was ever uncovered to support that, various other than the password of "do what the takes to obtain the inspector off your back."

Personally, I"d rest it up, and separate lighting native outlets (I detest being left in the dark when something plugged right into an outlet reasons a trip.) However, if the mass of what is happening at the outlets is "nothing" or "wall-wart because that a phone" or basically if girlfriend don"t expedition it much, you can leave it alone. It"s certainly going to it is in cheaper to perform nothing.

Without knowing how plenty of devices were lights .vs. Outlets, I"d carry out lighting and probably at least 2 outlet circuits, probably 3. Yet I have a certain philosophy, and also there"s no code need to carry out it my way.

enhance this answer
reply Nov 17 "14 in ~ 16:44

111k66 gold badges112112 silver- badges245245 bronze title
include a comment |

Ontario, Canada Code: 15 systems on a 15Amp circuit breaker

1 irradiate = 1 unit;

a typical plug-in outlet = 2 units

My comments

this requirements revision: A typical 15 Amp circuit have the right to support 300 LED light bulbs (60W equivilent output) there is no blowing!

suggest a different circuit because that a computer system system

enhance this price
answered jan 18 "17 at 13:49
Jonathon David WhiteJonathon David White
2111 bronze badge
include a comment |
There room some presumptions that to be missed in this discussion, so ns will point out the lacking questions by listing them here.

a. Complete length of strength supply wiring?b. Full wire gauge.

c. What is the intended maximum load ?

d. What is the circuit breaker rating?

e. Is the power supply circuit "shared" by outlets and lighting? (this is a usual mistake)

the answers rather frankly offered advice without even considering or discussing facts around the design of this present circuit.

my first reaction analysis this, what this does not sound prefer a fine designed system. That looks prefer there to be too couple of funds or not sufficient talent to actually design a for sure and an excellent working electric system in her home.

(I was actually looking for a quite schematic because that a 4 method switch come 19 LED recessed ceiling lamp so I might share that with a co worker that is just starting out and also is passionate to learn)

Here is what happens as soon as you uncover this type of work:

usually there are other mistakes made that come ago to haunt you when the walls go up!

lights flicker or breakers pop once everyone wakes up, or walk to take a shower, or usually whenever over there is too much fill for the circuit.

is the wire even adequate because that the meant load. Remember electrical safety 101......when every else fails the cable should be able to hold up....but if the cable is wrong, or the fill is just ridiculous due to the fact that someone wanted to it is in cheap...then, an episode the weenies....burnpile chicken anyone?

other points I see as soon as I walk looking as soon as I check out underbuilt circuits:

grounds not set up or not correctly....zap...thank you might I have actually another.

wire damaged during installed.....nice weld joint in her switch crate dude! the charcoal discoloration really brings the end the curtains in this room!

wrong size breakers..pop....pop...pop...pop...

GFCI not installed correctly or not at all in the "best locations"....might also just pole a fork in the outlet and get it end with....seriously.

wire cables not routed effectively or hanging dangerously near warmth sources of sharp points and also objects.

943 cable cables all "homerunned" in a chop bundle about one foot in diamter...squeezed in addition to zip ties understand to pass v tight attic spaces that travel towward the panel breaker box. Yes, that creative...Yes, it is sexy looking therefore tight........mister voltage drop as result of wire heat and other electromagnetic forces (inductance) simply caused a major power difficulty that this family members will invest years and countless thousands do the efforts to number out why irradiate dim and fade...randomly...even once the use on the circuit is within "spec".

See more: Snow Was Quickly Pil In This Passage You Can Best Infer That A

I am an avionics"s the wires"s the freaking wires. Overbuild your will thank yourself because that spending a little more today...