ns am moving to one all electric apartment and also have a gas dryer. It is 3 year old. Deserve to it be converted to an electrical dryer? exactly how would I find someone to carry out this?


*


In general, no friend can"t perform this.

You are watching: Can a gas dryer be converted to electric

I suppose it"s possible that the manufacturer uses plenty of of the very same parts in between their gas and also electric models and also you might buy enough parts to do a conversion, but this would most likely cost much more than just buying an electric dryer in the first place.

But I"ve never seen a supported conversion kit - my advice: sell the gas dryer and also buy one electric.


*

You might convert it to use propane. That way you can keep making use of it. There space some videos about how to perform it.

Don"t know around how it will impact its working, or longevity.

https://www.youtube.com/watch?v=7MC2xuQqQW0

*


*

*

I intend you could, yet it doesn"t make sense. Gas is practically always cheaper than power per kilowatt. Therefore the operational cost is much less for the gas dryer. In enhancement gas produces much more BTU than electric so the gas dryer is more efficient and will dried the clothing faster. The only down next is the initial expense of the appliance is a bit higher for a gas dryer


Yes, a mechanical regulate gas dryer can be converted to an electrical dryer, simply as a mechanical control electric dryer can be convert to gas. The newer computer system controlled appliances might be problematic because that conversions, i.e., also expensive to do it a feasible option, (but who knows, probably flip a dip move on the board and it might work just fine). Otherwise, ~ above a mechanical manage dryer, many of the parts are the same whether gas or electric(or propane i m sorry is a reasonably simple, safe and inexpensive conversion indigenous NG).

While ns am familiar with Alliance products, i am fairly certain many dryers would certainly be the same. As far as dryers go, manufacturers save time and money by having actually most choices built right into the cabinets and also controls, in various other words, most of the cabinet and also moving parts of dryers room the very same whether gas or electric, and also have been unmodified for decades. What has changed, and not constantly for the better, room the controls and also their consoles/panels. Mechanical controls seldom if ever malfunction in a residential setting, whereas computer system controls have the right to go negative for a variety of reasons and also are expensive to replace.

The an initial thing would be to remove the parts certain to the gas dryer:the gas lead-in pipe assembly, shut turn off valve and also elbow, igniter and bracket assembly, burner assembly, the coils and gas valve assembly and also mounting bracket, warm duct shroud, combustion duct and limit thermostat, and the 110 power lead in cord.Then we would replace every one of the over with an electric heater kit (either 208 or 240 volts) which consists of all cable assemblies, heat fuse assembly, and limit thermostat, the mounting feet are currently in the heater duct that attaches to.Next come the 220 terminal block and also terminal block shield which connect to the backside the the behind bulkhead assembly, the mounting holes are currently there on every dryers as room the 220 terminal block accessibility cutout and also cover ~ above the behind of the cabinet, through which is set up the 3 prong or 4 prong 220 lead in cord.

And finally the wiring, the protection cabinet harness assembly and wire harness assembly details to the an equipment (front or behind controls) must be changed to the versions suitable to the machine"s serial number and the new electric heater.

For any looking in ~ a gas to electric conversion, it would be wise to inspect/replace items such as the (2) cylinder rollers, and the (2) cylinder roller shafts, the cylinder belt, the idler lever and wheel assembly, and also the versatile exhaust venting outside of the maker which may become clogged v lint.Since most of the working parts must be removed from within the dryer because that this conversion, the is quite accessible to use of a vacuum to remove all lint inside the cabinet or the vents at the rear, and all the holds the motor and also exhaust fan assembly is 2 screws and a strength clip, so the doesn"t take lengthy to eliminate it and blow out any lint i m sorry has collected inside the blower housing and on the motor.

See more: How Many Electrons Will Aluminum Gain Or Lose When It Forms An Ion?

The absent panel on many dryers has actually 2 5/16 screws holding it on, and if you have actually someone who can remove it girlfriend can inspect to view if over there is a buildup of lint inside, if so you should contact for service, or if therefore inclined, unplug the maker and carefully vacuum out whatever lint is easily accessible because a buildup the lint inside the dryer is a fire peril whether gas or electric.