mine high placed third brake light stops working. It works on and also off.I think there's a loose connection. I have the right to not number out how to acquire to the to inspect it.I require to uncover a way to obtain to it come either replace the irradiate or to make certain it's no a connection problem.I have actually tried several ways to eliminate it without any luck.


You are watching: 2008 chrysler town and country third brake light replacement

*

The bulbs space led and also the totality CHMSL need to be replaced as a unit. You have to open liftgate take turn off panel climate spoiler below are pics.CLICK come ENLARGE!
*

*

*

*

here are the wiring diagrams and also a overview to assist you see what the trouble is. The power to the 3rd brake light originates from the TIPM and also there are numerous fuses that run it. An initial see if the brake irradiate is acquiring power at the light.https://www.civicpride-kusatsu.net/articles/how-to-use-a-test-light-circuit-testerthen inspect the fuses,https://www.civicpride-kusatsu.net/articles/how-to-check-a-car-fuseHere is the fuse location and the diagrams (below) If all of the fuses are good then the most likely the TIPM is going the end which they had troubles with. A shop will must program the unit unit in.Please permit us know what you find.Cheers, Ken
2006 chrysler town and country behind brake lights not working. Upper brake light is functioning rear turn signals no working. Behind running lights work?
The third center brake irradiate is not working I changed the irradiate bulb, however still does not work. I additionally think the fact it go not job-related is the my examine engine light has come on. I don not know if that is the connecting or what.
i doubt the light has anything to carry out with the examine engine light. Have a skilled scan because that codes because this might be a tpim module problem. The brake light switch sends out power come the tpim then to the light. Only a local experienced can scan for this. Additionally check engine difficulties will likewise come up.
ns did examine it out, but the just code the uncovered was Brake move problem, yet the funny component is the I changed it twice and also when i went ago the 2nd time lock told me the it might be the car"s computer which I may need come change. Plus together I claimed I changed the bulb in the 3rd brake light and also it does not revolve on. Therefore I perform not know what the difficulty may be.
the is what a tpim module is, the car"s computer and also it operation the third brake light the is why it does no work.
You can see by the snapshot it may already be wired direct, so view if strength is going to the light then backtrack cable to check out if it is broken. If no power, if power is over there then inspect the ground wire which is in lift-gate.
The brake light on the driver side works and the middle top brake irradiate works, but the one on the passenger side does not. Ns have readjusted the bulbs 2 times and still does no work. Every lights room ok!


See more: How Many Valence Electrons Does A Conductor Generally Have? ?

If after replacement the pear does not work, I would recommend check the contacts in the bulb connector. The connectors will sometimes develope burn clues on their contacts whereby they satisfy the bulb. Look at in the bulb connector. Carry out you see any burn marks, corrosion, etc? If you execute you can shot using a tiny piece of well grit sand paper to clean up the contacts. Likewise pry the contacts out slightly come make certain they space making a solid connection. If this walk not work you will need to check if over there is voltage come the connector. This will call for a voltage test light ($10) or a multi meter ($50+) indigenous your local auto parts store. Using a test light, affix it to a good ground and with the brake pedal depressed touch the test light tip to the positive contact in the pear connector (you have the right to touch it come both if her not certain which one it is). If your test light lights up you have actually power at the connector, if no you will have to trace the circuit ago to where you have actually power.