If the is simpler to walk increase a hill 보다 to drive up, you may have a negative fuel filter. Review on to learn exactly how to replace the fuel filter on your Honda Accord.


This article applies to the Honda Accord (1990-2002).

You are watching: 2004 honda accord fuel filter location

For Honda owners that don\"t perform continual maintenance, among the item that ultimately needs to be changed is the fuel filter. Yet it\"s not as bad as it sounds. If you room overdue for this task, girlfriend may notification that under tougher and steeper road problems your Accord might feel sluggish. A experienced can perform this project pretty quickly, but at a price. It may take friend a bit longer, yet you have the right to do it for a fraction of the cost. Select either option, yet remember that running with a poor fuel filter will at some point lead come clogged fuel injectors in ~ best. In ~ worst, the may bring about a damaged fuel pump and fuel system.

\"*\"

Materials NeededNew fuel filter10, 14, and 17 mm flare seed wrenchesFluid record panShop rags
Warning

Perform this task in a well-ventilated area because the gas fumes might be harmful.


Step 1 – Disconnect battery and relieve the fuel mechanism pressure

Disconnect the an adverse (black) terminal indigenous the battery. Then, eliminate the gas cap to relax gas push from the fuel system.

\"*\"
Figure 1. Disconnect negative battery terminal before starting.
\"*\"
Figure 2. Remove gas cap to relax fuel system pressure.
Pro TipsTo relax the fuel system pressure, you can likewise loosen the gas push bolt in ~ the end of the fuel rail. If you use the bolt method, make sure that friend re-tighten it once the project is finished.If girlfriend don\"t relax the pressure before starting, it will certainly be more challenging to eliminate or unplug every the vital parts.

Step 2 – locate the fuel filter

The fuel filter ar is different on particular model years.

1990-1994: Accord fuel filters are located on the passenger\"s side firewall.1995-2002: Accord fuel filters are situated on the behind of the engine, near the brake grasp cylinder.

Step 3 – eliminate the lower fuel line and the upper fuel line Banjo bolt

Once you have actually located the fuel filter, usage the 14 mm wrench and also rotate counterclockwise to loosen the nut from the reduced fuel line. Place the fluid capture pan under this area to catch any type of spilled gas. As soon as the seed is removed, traction the reduced fuel line off and set it aside. Then, use the 17 mm flare nut wrench to loosen the Banjo bolt on top fuel line. Revolve the wrench counterclockwise to ease the bolt, and also then eliminate the fuel heat by hand.

Figure 3. Remove 14 mm bolt indigenous the bottom fuel line.
\"*\"
Figure 4. Eliminate 17 mm Banjo bolt from upper fuel line.

Step 4 – eliminate the clamp bolts

Using the 10 mm flare nut wrench, unfasten 2 bolts from the clamp that host the fuel filter in place.

Figure 5. Remove two 10 mm bolts from fuel filter clamp.

Step 5 – replace the fuel filter and also reattach the clamp

Unclip the alignment feet holding the optimal of the fuel filter in place, and also then remove the fuel filter indigenous the clamp. Dispose of the old filter and also place the brand-new fuel filter in the clamp. Then, insert the fuel filter clamp to its initial location and also secure it v the 2 10 mm bolts.

Figure 6. Remove and also replace the fuel filter from the clamp.

Step 6 – Reconnect the upper and also lower fuel lines

Before reconnecting the top fuel line, insert two brand-new washers. Then, tighten the 17 mm Banjo bolt come a snug fit. Reconnect the reduced fuel line, and also secure it v the the 14 mm bolt come a snug fit together well.

Figure 7. Re-attach the bottom fuel line.
Pro Tip

Your instead of filter may have come through replacement washers. If not, you need to replace the washers that the upper fuel line when you replace the filter.


Step 7 – Re-check the fuel lines and bolts

Double inspect that her fuel lines and bolts are correctly secure.

Here room the bolts and also corresponding fuel lines:

One 14 mm bolt because that the bottom fuel lineOne 17 mm Banjo bolt because that the upper fuel lineTwo 10 mm bolts because that the fuel filter bracket

Step 8 – test the brand-new fuel filter

Tighten the gas cap (or gas pressure bolt in ~ the finish of the fuel rail), and reconnect the negative (black) battery terminal. Rotate the ignition to the \"ON\" position four times (without starting the engine). This is to prime the brand-new fuel filter with gas. Revolve the engine on because that the fifth turn. Through the auto running, inspect the new fuel filter for any kind of leaks. If girlfriend see any type of leaks, rotate off the engine and also re-tighten the fuel lines.

See more: St Louis To Denver Distance Between St Louis And Denver, Distance From Denver, Co To Saint Louis, Mo

\"*\"
Figure 8. Twin check the all fittings space secure.

Featured Video: Honda Accord Fuel Filter Replacement


Related Discussions and also Site